Greater duribility.
Better plunge characteristics.
Single flute - faster feed rates.
Single flute cutters should not be used in eccentric chucks.
...More Info
The Trend Solid Tungsten Carbide two flute cutters are turned, milled and ground from a solid piece of Tungsten Carbide and provide the greatest durab...More Info
Greater duribility.
Better plunge characteristics.
Two flute - finer finish.
Dimensions:
D=1/4 inch
D=6.3 mm
C=28 mm
OL=63 mm
Shank Diameter...More Info
Greater duribility.
Better plunge characteristics.
Two flute - finer finish.
Dimensions:
D=1/4 inch
D=6.3 mm
C=25 mm
OL=50 mm
Shank Diameter...More Info
Greater duribility.
Better plunge characteristics.
Two flute - finer finish.
Dimensions:
D=1/2 inch
D=12.7 mm
C=32 mm
OL=77 mm
Shank Diamete...More Info
Combination pierce and trim cutters.
Pierce and cut out apertures in laminate worktops.
Base of the cutter acting as a guide follower.
Single flut...More Info
Solid Tungsten Carbide economy cutter.
For use on short runs at 90 degree or 60 degree with Ref. S47/70, at 90 degree or 83 degrees with Ref. S47/7...More Info
Solid Tungsten Carbide economy cutter.
Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40.
Self guiding at 83 degrees with Ref. S48/...More Info
Cutter for trimming and bevelling timber, lippings and plastic laminate.
Can only be used in laminate trimming routers, or when straight fence guides...More Info
Solid Tungsten Carbide economy cutter.
Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40.
Self guiding at 83 degrees with Ref. S48/...More Info
Solid Tungsten Carbide economy cutter.
Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40.
Self guiding at 83 degrees with Ref. S48/...More Info
Solid Tungsten Carbide economy cutter.
Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40.
Self guiding at 83 degrees with Ref. S48/...More Info
Solid Tungsten Carbide economy cutter.
Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40.
Self guiding at 83 degrees with Ref. S48/...More Info
Solid Carbide rasp/burr.
Coarse cut.
For grinding, carving and shaping of glass reinforced plastics (GRP).
Not suitable for plunge cutting.
Use at...More Info
Solid Carbide rasp/burr.
Coarse cut.
For grinding, carving and shaping of glass reinforced plastics (GRP).
With twin roller bearings, is ideal for...More Info
Solid Carbide rasp/burr.
Fne cut.
For grinding, carving and shaping of glass reinforced plastics (GRP).
For plunge cutting.
Use at speed 10000 -3...More Info
Solid carbide burrs and rasps for removing welds and burrs in metal and hand engraving and sculpting wood and metal.Ref S49/20 has no bottom cut.Recom...More Info
Tooling for metal, glass reinforced plastic (GRP). plastic and wood. Carving, weld removal and drilling hole enlarging. Solid carbide head. For rem...More Info
Tooling for metal, glass reinforced plastic (GRP). plastic and wood. Carving, weld removal and drilling hole enlarging. Solid carbide head. For rem...More Info
Tooling for metal, glass reinforced plastic (GRP). plastic and wood. Carving, weld removal and drilling hole enlarging. Solid carbide head. For rem...More Info
Tooling for metal, glass reinforced plastic (GRP). plastic and wood. Carving, weld removal and drilling hole enlarging. Solid carbide head. For rem...More Info
Tooling for metal, glass reinforced plastic (GRP). plastic and wood. Carving, weld removal and drilling hole enlarging. Solid carbide head. For rem...More Info
Tooling for metal, glass reinforced plastic (GRP). plastic and wood. Carving, weld removal and drilling hole enlarging. Solid carbide head. For rem...More Info
Tooling for metal, glass reinforced plastic (GRP). plastic and wood. Carving, weld removal and drilling hole enlarging. Solid carbide head. For rem...More Info