Used for trimming plastic or plywood overlays.
Also for copy profiling with a template.
Dimensions:
D1=3/4 inch
D1=19.1 mm
C=50 mm
Overall l...More Info
Used for trimming plastic or plywood overlays.
Also for copy profiling with a template.
Dimensions:
D=5/8 inch
D=15.9 mm
C=5/8 inch
C=15.9 m...More Info
This is bearing guided and gives a smooth bevel finish for laminates and other materials.
Bearing follows the board beneath.
Dimensions:
D=15.1...More Info
Gives a smooth bevel finish for laminates and other materials. Bearing follows the board beneath.
1/4" shank 75ˇ bearing guided laminate trimme...More Info
This is bearing guided and gives a smooth bevel finish for laminates and other materials.
Bearing follows the board beneath.
Dimensions:
C=1/4 ...More Info
For picture hanging flush to the wall.
Plunge cutter & move forward, then retract out from entry hole.
A template is recommended.
For No8 & No1...More Info
These trimmers with shank mounted bearings are ideal for template guidance. Use for rebating and trimming edges. Extra care must be taken to avoide b...More Info
Shank mounted bearing profilers are ideal for template guidance.
Use for rebating and trimming edges only.
Extra care must be taken to avoid c...More Info
Shank mounted bearing profilers are ideal for template guidance.
Use for rebating and trimming edges only.
Extra care must be taken to avoid c...More Info
Shank mounted bearing profilers are ideal for template guidance.
Use for rebating and trimming edges only.
Extra care must be taken to avoid c...More Info
Shank mounted bearing profilers are ideal for template guidance.
Use for rebating and trimming edges only.
Extra care must be taken to avoid c...More Info
Shank mounted bearing profilers are ideal for template guidance.
Use for rebating and trimming edges only.
Extra care must be taken to avoid c...More Info
Shank mounted bearing profilers are ideal for template guidance.
Use for rebating and trimming edges only.
Extra care must be taken to avoid c...More Info
Self guiding cavetto style cutter, which follow the board edges for straight or curved work radius.
Dimensions:
C=5/8 inch
C=15.9 mm
D=34.5 mm
...More Info
Shank mounted bearing profilers are ideal for template guidance.
Use for rebating and trimming edges only.
Extra care must be taken to avoid cut...More Info
Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising.
Use on softwoods, hardwoods, MDF, plywood an...More Info
Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising.
Use on softwoods, hardwoods, MDF, plywood an...More Info
For producing ovolo and rounding over edge moulds, using a side fence or back fence.
Dimensions:
D=1/2 inch
D=12.7 mm
C=23/64 inch
C=9 mm
R=4....More Info
For producing ovolo and rounding over edge moulds, using a side fence or back fence.
Dimensions:
D=5/8 inch
D=15.9 mm
C=13.5 mm
R=6.3 mm
Overa...More Info
For producing ovolo and rounding over edge moulds, using a side fence or back fence.
Dimensions:
D=7/8 inch
D=22.2 mm
C=19/32 inch
C=15 mm
R=9...More Info
Attractive edge moulds, a full corner bead can be produced by making a second pass at 90° . Used on all man-made boards such as medium density fib...More Info
Attractive edge moulds. A full corner bead
can be produced by making a second pass at 90 degrees.
Dimensions:
D=1 1/32 inch
D=26 mm
D2=22 mm...More Info
Ideal for following template. It is advisable that the template is at least 5mm thicker than the cut length of the tool.
Dimensions:
D=22 mm
C=2...More Info
Ideal for following template. It is advisable that the template is at least 5mm thicker than the cut length of the tool.
Dimensions:
D=22 mm
C=2...More Info
This 'roughing' trimmer, leaves an overhang of 3mm, for secondary final trim.
Dimensions:
D=1/2 inch
D=12.7 mm
C=1 inch
C=25.4 mm
B=19.1 mm
E...More Info
This 'roughing' trimmer, leaves an overhang of 3mm, for secondary final trim.
Dimensions:
D=1/2 inch
D=12.7 mm
C=1 inch
C=25.4 mm
B=19.1 mm
E...More Info