Laminate Trimmers, Router Cutters, Trend Routing on Corroy Products

Shop By Brand

Browse By Brand

Laminate Trimmers

Trend Routing > Router Cutters > Laminate Trimmers

Returned 20 Results

TREND 46/06X1/4TC COMBI TRIMMER A1=90¡ X A2=45¡

A self-guided combination trimmer. A 90 degree trim is obtained by engaging the bottom half. A 45 degree trim is obtained by lowering the cutter.... More Info

£82.75 INC VAT

TREND 46/6BX1/4TC BEVEL TRIM A=45¡ X 27MM DIA

Cut a wider edge line, at an angle of 45 degrees. A 16mm bearing is supplied as standard. A larger 19mm bearing will spread the wear of the cutting... More Info

£76.34 INC VAT

TREND 46/6CX1/4TC BEVEL TRIM A=30¡ X 26MM DIA

Cut a wider edge line, at an angle of 30 degrees. A 16mm bearing is supplied as standard. A larger 19mm bearing will spread the wear of the cutting... More Info

£68.86 INC VAT

TREND 46/7/50X1/4TC B/GUIDED GLAZING BAR 10MM RAD

The glazing bar ovolo cutter is bearing guided to speed setting-up and to enable curved frames to be moulded. Dimensions: D=28 mm C=19 mm B=12.7... More Info

£118.84 INC VAT

TREND 46/75X1/2TC B/GUIDED CLASSIC 6.3MM RAD

Self guiding classic cutters with facility to change profile by fitting larger bearing and varying the depth. Supplied with two bearings. Dimensio... More Info

£91.38 INC VAT

TREND 46/7X1/4TC DOUBLE OVERLAP A=90¡ X 18MM DIA

Trimming top and bottom surfaces simultaneously with bearing following the board. Two fluted. Increased productivity. Dimensions: D=18 mm C... More Info

£104.53 INC VAT

TREND 47/2X1/4TC TRIMMER A-90¡ X 18MM DIA

For trimming the lipping of plastic overlay, and for rebating and machining wood, Duralium and plastics. Tungsten Carbide Tipped. Use at speed 12... More Info

£67.44 INC VAT

TREND 47/40X1/2TC PIERCE & TRIM 12.7MM DIA TWO FLUTE

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Dimension... More Info

£74.09 INC VAT

TREND 47/4X1/4TC PIERCE & TRIM 6.3MM DIA 257123

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Single flut... More Info

£37.13 INC VAT

TREND 47/50SX1/2TC PIERCE & TRIM 1.27MM X 123MM OL

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Specially d... More Info

£92.69 INC VAT

TREND 47/50X1/2TC PIERCE & TRIM 12.7MM DIA

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Will trim b... More Info

£92.69 INC VAT

TREND 47/7X1/4TC COMBI TRIMMER A=60¡X12MM DIA 253362

For trimming top & lip. Economical cutters, perform 3 functions: 1. To top trim the overlay at 90 degrees. 2. To trim the overlay at 45 degrees o... More Info

£43.56 INC VAT

TREND S47/4X1/4STC PIERCE/TRIM 6.3MM DIA X 20MM CUT

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Single flut... More Info

£50.74 INC VAT

TREND S47/70X1/4STC ECONOMY TRIM A=60¡X6.3MM DIA 257121

Solid Tungsten Carbide economy cutter. For use on short runs at 90 degree or 60 degree with Ref. S47/70, at 90 degree or 83 degrees with Ref. S47/7... More Info

£45.83 INC VAT

TREND S47/71X1/4STC ECONOMY TRIM 7 DEG BEVEL

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/... More Info

£41.50 INC VAT

TREND S47/72X1/4STC ECONOMY V GROOVE 45 DEG

Cutter for trimming and bevelling timber, lippings and plastic laminate. Can only be used in laminate trimming routers, or when straight fence guides... More Info

£41.50 INC VAT

TREND S48/39X1/4STC ECONOMY TRIM A=90¡X6.3MM DIA X 38MM

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/... More Info

£41.50 INC VAT

TREND S48/40X1/4STC ECONOMY TRIM A=90¡X6.3DX52MM 257122

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/... More Info

£47.88 INC VAT

TREND S48/41X1/4STC ECONOMY 7 DEG TRIM GUIDED 6.35MM DI

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/... More Info

£41.50 INC VAT

TREND S48/42X1/4STC ECONOMY FLUSH & TRIM 6.35MM GUIDED

Solid Tungsten Carbide economy cutter. Self-guiding 90 degree trimming only with Ref. S48/39 & S48/40. Self guiding at 83 degrees with Ref. S48/... More Info

£41.50 INC VAT

Terms & Conditions

We Accept Visa, Mastercard,Switch,Maestro,Solo,Visa Electron and Delta.